INOMAX · Steel processing applications

Precision begins with coordinated motion.

Drive solutions for steel coil feeding, cutting, slitting and recoiling.

Real installations. Explained control architectures. Practical engineering detail from the supplied project material.

Cut-to-lengthTracking & flying shearsSlitting & winding

Explore the applicationsWatch site videos

Slitting / winding factory view from the supplied application material.

Application scope

Four routes. One coordinated material flow.

Each cutting or winding mechanism has its own motion requirements. The drive system must fit the machine, the material and the required product range.

Stop cut-to-length

Measure strip travel, decelerate to position, hold for the cut and clear the sheet.

Tracking shear

Synchronize a moving cutting table to the strip, cut and return within the available cycle.

Flying shear

Coordinate material travel with cutter motion and phase through the cutting window.

Slitting & recoiling

Maintain compatible section speeds and suitable winding tension as coil diameter changes.

PROJECT CONTEXT

Application overview

From coil handling to finished sheets and slit coils, coordinated drives connect the mechanical process with repeatable motion control.

Factory view from the slitting / winding source set.

The application challenge

Steel strip must pass through feeding, leveling, buffering, cutting and discharge stages without losing the relationship between actual strip travel and cutter motion. Different cutting mechanisms require different motion sequences.

The INOMAX contribution

The supplied material documents INOMAX drive installations in steel-processing cabinets, supported by line diagrams and operating videos. The scope presented here is the drive and control application; the material does not establish supply of the complete mechanical line.

How to read this casebook

This is a consolidated application summary covering several configurations. Photographs and source diagrams are project evidence. Selection advice, commissioning steps and explanations of control behavior are engineering guidance, not recorded acceptance results.

PROJECT CONTEXT

Evidence, scope and technical boundaries

The source folder covers stop cutting, tracking cutting, flying shears, slitting / winding, oil-grinding lines and production-line layouts.

Evidence available What it supports What it does not establish
Cabinet photographs INOMAX drives installed with electrical components and field wiring. A verified drive-by-drive bill of materials or electrical rating.
English system diagrams Axis roles, material path, feedback relationships and PLC / HMI coordination. An as-built circuit drawing, fieldbus protocol or final I/O allocation.
Operating videos Examples of feeding, cutting, discharge and winding behavior. Certified speed, length tolerance, availability or energy savings.
Suppression OFF / ON clips A supplied demonstration of strip-motion behavior under two labeled conditions. A matched, instrumented vibration test or quantified improvement.

The reviewed set contains 37 still images and 17 videos after duplicate removal. Customer identity, installation date, voltage, motor ratings and acceptance measurements are not established.

PROCESS & CONTROL

The material path through the line

The supplied layout combines coil preparation, strip conditioning, longitudinal processing and cross-cut delivery. Actual equipment combinations vary by line.

Supplied production-line layout; a reference arrangement, not a verified single-site as-built drawing.

Entry and preparation

Coil loading and uncoiling release strip into the entry section. Pinch rolls establish traction; the leveler conditions the strip before downstream measuring and cutting.

Buffering and processing

Loop sections separate the speed behavior of adjacent machine groups. Strip guides and pinch rolls lead material through the slitter or the measured-feed section.

Delivery

The cross-cut station produces sheets; conveyors transfer them to stacking. A slitting-only route instead delivers multiple narrow strips to a recoiler.

PROCESS & CONTROL

Four application routes

Choose the control sequence around the machine mechanism and the product mix, then match the drives and feedback to that sequence.

Application Material during cutting Control focus Mechanical constraint
Stop cut-to-length Feed pauses for the cut. Measure strip travel, decelerate, hold, cut, restart. Repeated acceleration and the available upstream buffer.
Tracking / carriage shear Strip continues while the cutting table follows it. Synchronize carriage travel, cut, then return and reset. Carriage stroke, acceleration and return time.
Rotary flying shear Strip continues through the cutting window. Coordinate cutter phase and peripheral speed with strip motion. Cutter inertia, cyclic torque and permitted motion profile.
Slitting and recoiling Strip moves through longitudinal knives into coils. Coordinate line speed and winding tension as diameter changes. Knife setup, traction, strip separation and coil buildup.

The rotary arrangement is shown in the supplied flying-shear diagrams. Other supplied shear videos illustrate line operation; the exact cutter mechanism is not inferred solely from a video filename.

PROCESS & CONTROL

Different feedback signals do different jobs

The diagrams distinguish motor feedback, strip measurement and cutter or carriage feedback. These signals are not interchangeable.

Supplied flying-shear diagram showing feed, measuring-wheel and cutter feedback.

Motor encoder

Reports the driven shaft’s speed or position. Roller diameter, gear ratio, backlash and possible strip slip affect the relationship between shaft movement and actual material travel.

Measuring wheel

Tracks strip travel and speed near the cutting section. Wheel circumference, encoder scaling, contact pressure and surface slip are key checks when the commanded and measured sheet lengths disagree.

Cutter / carriage feedback

Reports the cutting axis position or phase. The controller uses this feedback together with material travel to coordinate the cut. The PLC manages machine sequencing; the HMI carries order length, quantity and operating status.

STOP CUT-TO-LENGTH

Stop cutting: measure, stop, cut, discharge

In a stop-cut arrangement, the feed axis positions the material before the stationary cutting action. Discharge conveyors then clear the sheet.

Source architecture: feeder motor feedback, measuring wheel, cutter and two discharge drives.

Feed and position

Use measured strip travel to approach the requested length. Deceleration must be coordinated with traction and the available stopping distance so that the material arrives at the cutting position consistently.

Hold and cut

The machine sequence should confirm the required stopped / positioned condition before allowing the cut. The cutter’s ready and completed states determine when feeding can resume.

Transfer and repeat

Conveyors remove the cut sheet toward stacking. Upstream feeding and loop management must accommodate the repeated stop-start demand of the measuring section.

STOP CUT-TO-LENGTH

Stop-cut installations and operating context

The field material shows both the electrical installation and the physical strip path: the case depends on the interaction between the two.

Drive cabinet evidence

Several INOMAX drives are visible in the supplied cabinet close-ups. Different drive sizes and adjacent electrical components indicate multiple controlled machine functions; exact axis assignments need the final electrical drawings.

Strip handling evidence

The site photographs and operating clip show strip passing through a looped feed path into the cutting section. The loop provides physical buffering between upstream supply and intermittent downstream demand.

Engineering implication

Tune the feed cycle together with loop behavior and discharge clearance. A faster drive ramp alone does not prove higher useful production if strip traction, buffer travel or stacking becomes the limiting factor.

STOP CUT-TO-LENGTH

Stop cutting: practical control priorities

Length consistency is a system property. Drive tuning, material measurement and mechanical condition must be checked together.

Operating issue Likely checks Useful validation
Length error grows with speed Measuring-wheel slip, scaling, deceleration behavior, measurement timing. Compare actual sheet length at several approved line speeds.
Length shifts after a stop Material movement during hold, roller pressure, backlash, cutter sequence. Trend strip position through hold, cut and restart.
Loop approaches its limit Upstream reference, loop sensing, ramp mismatch and buffer capacity. Observe the full repeated cutting cycle, not one cut.
Sheets collide or stack poorly Discharge speed, conveyor ready logic, sheet-clear indication. Run the intended length mix and stack-change sequence.

Commissioning guidance. The source set does not contain measured length-error trends or a signed stop-cut acceptance report.

TRACKING SHEAR

Tracking shear: cut while the carriage follows

The supplied tracking-shear drawing places the cutter on a moving table. Material motion and carriage motion meet during a defined cutting interval.

Source tracking-shear architecture with material measurement and cutting-table motor feedback.

Synchronize

The measuring wheel provides strip travel and speed. The carriage axis accelerates toward the material speed and reaches the required position relationship before the cutting action.

Cut in the tracking window

The table follows the moving strip while the cut is completed. Speed mismatch during this interval can load the strip or disturb the cut; the permitted window depends on the machine design.

Return and re-arm

After separation and clearance, the carriage returns to its start position. The next cut must fit within the available stroke and return cycle; shortening the product length increases the demand on this motion sequence.

TRACKING SHEAR

Tracking shear: motion and machine limits

The field video shows a driven cutting-table assembly and strip passing through the machine. It supports the application description, without supplying cycle-time measurements.

Frame from the supplied tracking-shear operating video.

Axis sizing

Evaluate carriage mass, transmission ratio, friction, travel and acceleration. Peak torque and repeated duty matter alongside continuous motor power.

Sequence coordination

Define the start position, synchronized interval, cutting completion, clearance and return-complete states. Loss of measurement or an axis fault must be handled by the machine’s validated control sequence.

Acceptance focus

Check cut length over the intended product range, synchronization during the cut and return margin before the next cycle. Record actual operating conditions so that repeat runs can be compared.

FLYING SHEAR

Flying shear: speed and phase at the cut

The rotary flying-shear diagram coordinates the feed axis with cutter position feedback through a dedicated flying-shear program.

Source rotary flying-shear architecture. The actual machine determines the permitted motion profile.

Material as the reference

Actual strip travel determines when the next cut is due. Measuring-wheel feedback gives the cutting control a material-based reference rather than relying only on the feed motor command.

Cutting window

The cutter phase and the speed at the blade-to-strip interface must follow the required profile through the cutting window. Outside that window, the cutter can change speed according to the permitted motion cycle.

Changing orders

Cut length and order quantity are shown at the HMI in the full-line drawing. A shorter requested length changes cycle frequency and may require a different validated operating envelope.

FLYING SHEAR

Flying-shear line: coordinated entry to exit

The full system diagram connects uncoiling, pinch feeding, leveling, a buffer loop, measured feeding, flying cutting and discharge.

Supplied full-line system diagram with PLC communication and HMI order inputs.

Separate the process sections

The upstream group supplies and levels the strip. The buffer loop accommodates speed differences before the measured-feed and cutting section.

Coordinate the references

A line-speed request alone is insufficient: the cutting control needs material travel, cutter phase and machine status. The PLC communication shown in the drawing ties the sections into a coordinated sequence.

Manage downstream flow

Conveyor and stacking readiness must be part of the production sequence. Continuous cutting does not remove the need for reliable sheet separation, discharge and stack management.

FLYING SHEAR

Short and medium sheet operating examples

Two supplied videos are labeled for short-material and medium-length flying-shear applications. Both show cutting-line discharge in operation.

Short-sheet duty

At a given strip speed, shorter sheets require more cuts per unit time. This increases the importance of cyclic torque, cutter recovery and downstream sheet spacing.

Medium-length duty

Longer intervals between cuts change the motion profile and discharge behavior. A profile suitable for one length should not be assumed suitable for the entire order range without validation.

What the clips demonstrate

The clips provide useful views of the cutter area and conveyor handling. No calibrated scale, speed trace, actual sheet-length record or confirmed cutter kinematics accompanies these clips.

FLYING SHEAR

Flying-shear drive cabinet integration

The source photographs show multiple INOMAX drives integrated into cabinets with wiring ducts, terminals and associated control components.

Application evidence

A bank of compact drives and larger units appears in the flying-shear source set. These images demonstrate cabinet integration; they do not by themselves identify each motor’s rating or duty.

Commissioning access

Maintain a clear axis schedule linking each motor, drive, feedback device and control function. Parameter backups and labeled connections make commissioning and later replacement more manageable.

Product identification

Source filenames identify this set as an ACS880 application and identify a stop-cut clip as ACM series. Exact installed variants, firmware and communication options require nameplate and configuration confirmation.

STRIP HANDLING

Uncoiling, leveling and buffer control

Stable delivery to the measured-feed section begins upstream, where coil inertia, strip traction and available loop travel change during production.

Coil entry arrangement from the oil-grinding / finishing source set.

Uncoiling

The coil must release strip without creating excessive pull or uncontrolled slack. Coil diameter and inertia change through a run; the chosen drive mode and brake arrangement must suit the mechanical design.

Leveling and pinch feeding

The leveler and pinch rolls must maintain the required transport relationship while handling process load. Drive settings cannot compensate for unsuitable roller pressure, worn surfaces or mechanical misalignment.

Loop management

The loop separates intermittent or changing downstream demand from upstream supply. Its usable range, sensing and response must be coordinated with ramps, starts, stops and tail-out.

SLITTING & RECOILING

Slitting: one wide strip, multiple narrow lanes

Longitudinal knives divide a wide strip into narrower lanes. Drive coordination must preserve strip transport through the slitter and toward winding.

Knife and spacer setup

The required widths are established mechanically by the knife and spacer arrangement. Knife clearance, overlap, alignment and material properties influence edge quality; they are not determined by a VFD speed setting.

Transport relationship

The driven rolls and slitter section must maintain a compatible surface-speed relationship. Unwanted speed differences can create strip pull, slack or marking.

Downstream separation

Multiple lanes must remain correctly guided and separated through the path to the recoiler. Tension distribution and coil buildup can differ between lanes and depend on the complete mechanical arrangement.

SLITTING & RECOILING

Recoiling: diameter changes the drive duty

The winding section must maintain suitable strip tension while the coil radius and rotational speed change.

Speed relationship

For a given strip speed, recoiler rotational speed decreases as coil radius increases. The control therefore needs an appropriate diameter estimate or measurement, with the correct mechanical scaling.

Torque relationship

At the coil surface, steady winding torque is approximately strip tension multiplied by coil radius. Motor-side demand also includes gear ratio, efficiency, inertia and acceleration or deceleration.

Control implementation

Open-loop torque scheduling, dancer feedback or load-cell feedback are possible engineering approaches. The source images show winding results and strip routing, but do not confirm which tension-feedback method was installed.

SLITTING & RECOILING

Slitting and winding: quality and stability

A coordinated drive system supports stable transport; finished-coil quality still depends on knives, strip condition and winding mechanics.

Observed symptom Review together Record during validation
Loose or uneven winding Tension reference, diameter estimate, strip separation and winding mechanics. Coil diameter, tension feedback if fitted, torque and speed.
Strip wandering Entry alignment, guides, roller parallelism and uneven lane tension. Lateral position across acceleration and steady running.
Edge burr or surface marking Knife condition / setup, material properties, roller contact and cleanliness. Product width, edge condition and surface inspection.
Instability during ramps Inertia compensation, speed-reference coordination, loop condition and friction. Trend the ramp, torque demand and relevant feedback together.

These are diagnostic priorities, not a record that these defects occurred on the supplied installations.

STABILITY DEMONSTRATION

Resonance suppression: supplied OFF / ON clips

The winding source set includes two videos explicitly labeled “resonance suppression OFF” and “ON”. They show the strip span near the processing equipment.

What can be concluded

The source owner provided a visual comparison intended to demonstrate strip-motion stabilization. It is appropriate to present the two conditions with their original labels.

What remains unmeasured

The camera viewpoints differ, and matched speed, tension, material thickness and instrumented vibration data are not supplied. A numerical reduction or guaranteed performance improvement cannot be calculated from these clips.

How to validate the benefit

For a future comparison, hold material, speed, tension and camera position constant. Capture drive speed / torque traces and an agreed vibration or strip-displacement measure before and after tuning.

ADJACENT APPLICATION

Related application: oil-grinding / coil finishing

The oil-grinding source folder expands the case beyond cutting to a continuous coil-processing application with entry, transport and drive-cabinet evidence.

Process context

The material shows coil handling and strip movement through a processing line. The folder is identified as oil grinding; the exact abrasive stages, treatment fluid and finish specification are not documented.

Drive role

Consistent transport and coordinated section speeds help maintain stable strip movement through the process. Entry and exit behavior must be coordinated with the finishing equipment and winding arrangement.

Evidence boundary

The cabinet photo shows INOMAX drives and associated control hardware. This supports the installed-drive application, without establishing surface-finish results, energy savings or a complete process-machine supply scope.

ENGINEERING DELIVERY

Cabinet engineering and integration checks

Turn the application diagram into an axis-by-axis electrical design before final equipment selection.

Design area Information to confirm Why it matters
Motor and load Motor nameplate, feedback type, gearing, inertia, duty cycle and overload. Separates continuous current requirements from cyclic peak demand.
Power and braking Supply voltage / frequency, deceleration energy and braking arrangement. Avoids selecting solely by nominal motor power.
Control interface PLC, HMI, I/O, communication protocol, update timing and fault behavior. Makes machine sequencing and diagnostics explicit.
Installation Cabinet temperature, cooling, clearances, grounding and cable routing. Supports reliable operation in the actual environment.
Machine functions Permissives, limits, stop behavior, guards and restart sequence. Ensures the drive application fits the machine’s validated design.

No common DC bus, regenerative front end, specific safety rating or fieldbus protocol is claimed for the photographed systems.

ENGINEERING DELIVERY

Commissioning: from single axis to production

A practical commissioning sequence proves measurement and motion first, then tests the complete product and operating range.

Stage Work to complete Evidence to retain
Preparation Verify motor / drive data, axis names, wiring, limits and feedback direction. Approved axis schedule and baseline parameter backup.
Measurement Calibrate roller or measuring-wheel scaling; verify encoder counts and polarity. Measured travel versus displayed travel.
Single-axis operation Validate direction, ramps, torque / current response and permitted travel. Trend captures and exception list.
Coordinated operation Check feed / cutter or carriage synchronization, loop behavior and discharge. Cycle traces and observed sequence timing.
Product validation Run agreed materials, lengths, speeds and coil-diameter conditions. Sheet / coil inspection records and acceptance results.

Perform commissioning within the machine builder’s approved procedures. No commissioning report or test values were supplied with the source media.

ENGINEERING DELIVERY

Acceptance criteria that make results comparable

Agree the test conditions and measurement method before quoting a project outcome.

Operator station and discharge area from the stop-cut field photographs.

Cut-to-length and shearing

Define the material, thickness, width, target lengths and line speeds. Measure actual sheets with an agreed method; retain individual results as well as the summary. Include start-up, steady running and order transitions where relevant.

Slitting and winding

Define product widths, edge / surface requirements and acceptable winding condition. Include representative coil diameters and acceleration / deceleration behavior. If tension is measured, retain the calibrated feedback record.

Operational behavior

Test normal stop, restart, tail-out, stack change and relevant machine fault responses. Record the control version and parameter set used so that a later service visit can reproduce the accepted configuration.

PROJECT OUTCOME

Project value supported by the available material

The strongest documented result is application breadth: real INOMAX drive cabinets, several cutting architectures and visible strip-processing operation.

Supported finding Customer relevance Verification boundary
Drive installation evidence Shows practical integration with machine electrical systems. Exact quantities, model variants and ratings require an axis list.
Material-based feedback architectures Explains how feed measurement relates to cutting motion. Diagrams do not prove a particular achieved tolerance.
Several cutting configurations Helps select a control concept for different mechanical lines. No single maximum speed or product envelope is established.
Winding and stabilization examples Extends the discussion to tension and strip-motion stability. No quantified vibration, yield or downtime improvement is supplied.

The available material supports a technical application case. It does not establish a controlled comparison against another drive brand or measured return on investment.

EVIDENCE GUIDE

Source guide and engineering handover

Prepared from the supplied English cut-to-length project folder. Source photographs, system diagrams and selected operating videos form the visual foundation of this case.

Source group Material used in this summary Follow-up information for a specific order
Stop cutting English control diagram, drive cabinets, strip loop and discharge photographs, operating clip. Motor schedule, feed cycle and measured cut-length results.
Tracking shear English moving-table diagram and operating-video frame. Carriage stroke, mass, drive train and synchronized cutting window.
Flying shear Simplified / full-line diagrams, cabinet photos and short / medium sheet clips. Exact cutter mechanism, profile limits and validated product envelope.
Slitting / winding Strip, knife and coil photographs; suppression OFF / ON clips. Tension method, coil-diameter range and quality criteria.
Oil-grinding / layouts Coil handling, cabinet photo and reference production-line arrangement. Process specification, section speeds and final as-built layout.

Original media were selected for relevance; duplicate and Chinese-language versions of the same diagrams were not repeated. Third-party machine markings remain part of the source evidence, not a claim of INOMAX machine manufacture.

Operating evidence

See the material and machines in motion.

Watch selected operating clips from the project material. Videos load when played and have no audio. They show application operation; performance measurements are discussed separately in the technical sections.

Stop-cut line

Strip feeding and the cutting-line environment.

Tracking-shear assembly

Moving-table cutting equipment in the supplied operating example.

Short-material shear example

Source-labeled short-material application; no calibrated speed or tolerance supplied.

Medium-length shear example

Source-labeled medium-length application showing sheet discharge.

Resonance suppression OFF

Original source label. Operating conditions were not supplied as a matched test.

Resonance suppression ON

Original source label. Viewpoint differs from the OFF clip; no numerical reduction is claimed.

Buyer questions

From application concept to a defined scope.

Can INOMAX drives be used when replacing another drive brand?

Assess the complete axis before selecting a replacement: supply, motor current and overload duty, encoder interface, braking, PLC communication, dimensions and the existing motion program. Match the required control function as well as the electrical rating. These source files do not verify a drop-in replacement for a named competitor.

Which cutting arrangement should be selected?

Start with the mechanical machine. A stop-cut line positions and holds strip for cutting; a tracking shear follows the strip with a carriage; a rotary flying shear synchronizes cutter motion to continuously moving material. Required lengths, speed, strip properties, available buffer and cutter mechanics determine the feasible operating range.

What voltage and power range does this case cover?

The media do not supply a reliable project rating schedule. Provide the incoming supply and each motor nameplate, then add load, inertia, duty cycle and braking requirements. This allows an axis-specific selection without treating an unidentified photographed unit as a capability limit.

Can one controller operate the entire line?

The drawings show PLC coordination and a dedicated cutting-control function with material and axis feedback. The final division between PLC, motion controller and drive functions depends on cycle timing, feedback interfaces and the selected hardware. Confirm the required communication and I/O architecture before implementation.

How is cut-length accuracy improved?

Verify material measurement first: wheel scaling, contact and slip. Then examine mechanical backlash, traction, feed response and cutter synchronization. Set an acceptance test over the intended speed and length range. The source set contains no verified numerical accuracy guarantee.

How should winding tension be specified?

Provide strip material and dimensions, minimum and maximum coil diameter, speed range, winding mechanics and the proposed feedback devices. Define the desired winding quality and tension profile. Diameter compensation and transient duty must be evaluated together.

What is needed for commissioning and service?

Prepare the electrical drawings, axis schedule, motor / encoder details, PLC interface, operating sequence and target product range. Retain parameter and program backups, version records, trend captures and product measurements from the accepted run.

What should be confirmed before a delivery commitment?

Confirm the approved models, quantities, feedback and communication options, braking components, cabinet scope and test requirements. Delivery timing and the division of on-site responsibilities should be agreed against that scope; neither lead time nor a service commitment is stated in the supplied project media.

Discuss your application

Define the machine. Match the motion.
Verify the result.

Send the line layout, motor nameplates, supply voltage, material range, required cut lengths or slit widths, target speed and available feedback / PLC information.

info@inomaxtechnology.com

Top